TITAN™ V3 complete controller set

TITAN™ V3 Full Controller Set

Drop-In mosfet Type TITAN™ V3 Controller Set transforms an AEG into an advanced training replica. It offers a tactical advantage thanks to a lightning-fast trigger response and the ability to modify and customise the replica for any mission using 20 available functions. This is the most advanced and best model of GATE.

TITAN™ V3 controller breathes new life into an ASG electric replica.

TITAN™ offers new possibilities:
- Setting the trigger sensitivity
- Pre-cocking gain - adjustment of the time during which the spring is held pulled (shortens the time between pulling the trigger and firing the shot)
- Setting the fire mode selection modes
- Burst mode
- Fire rate setting
- Low battery notification
- Protecting the battery from damage
- "Sniper delay"
- Full cycle detection
- AUG mode - the option to set two trigger sensitivities (semi and full-auto)

TITAN™ Controller Set contains:

1st GATE™ Control Station
Normally update the firmware and/or carry out driver adjustments from home via a USB connection and a computer application. Connect and adjust your replica with a computer or laptop!

1. USB connection/plug
The USB connector works together with the GATE™ control station and provides full access to all functions offered by TITAN™ as well as the possibility to perform software updates of the control unit installed in a replica and the Tactical Programmer Card.

More detailed description of the TITAN™ controller:

SETTING THE TRIGGER SENSITIVITY
sensor of the second generation, which Control system of the trigger sensitivity. It is not necessary to dismantle the replica, just use the GATE™ control station. It enables the Customisation of the replica to the capabilities and individual preferences of the user.

CONFIGURABLE FIRE MODE SELECTOR (GEN. 2)
Two sensors can be programmed in three ways to select one of 6 functions:
- SAFE-SEMI-AUTO
- SAFE-SEMI-SEMI
- SAFE-SEMI-BURST*
- SAFE-BURST*-CAR
- SAFE-SEMI-BURST*/AUTO (short press and hold - BURST, long press and hold AUTO)
- SAFE-BURST*-AUTO (SAFE via a quick mode selection, if: SAFE-SEMI-SAFE)
*BURST means the firing of a series of shots.

CYCLE DETECTION
The TITAN™ control unit can precisely recognise the position at which a cycle should end . This completes a full firing cycle when the trigger is pulled (replicas without the TITAN™ system often jam if the trigger is pulled too short, if it does not end with a shot. TITAN™ eliminates this error).
This results in in:
- Automatic BURST mode, it is not necessary to set the time of the cycle of this series, the only thing necessary is to determine how many BBs should be fired
- Automatic pre-cocking available in each mode in the following fire mode selector settings: SEMI BURST and AUTO. Unlike conventional MOSFET modules, this setting does not need to be configured manually. Only the power of the spring preload needs to be set.
- ALWAYS FULL CYCLE - when the preload is switched off, TITAN™ ensures that the gear runs through a full cycle and the spring is released after firing. This ensures greater reliability of the replica.

PRECOMMENDATION (Gen.2*)
Victory in a duel often depends on fractions of a second, which is why the trigger responds thanks to Pretensioning with a speed that can be compared to that of a real firearm. The spring becomes drawn before, i.e. at the same Time, we warn that the use of this mode with strong springs will lead to faster wear of the internal parts of a replica.
There are two modes of the PRE-COCKING function:
1. AUTO - the spring is pulled after each shot
2. SMART - the spring is activated by a slower Press the trigger and a shot is released by a quick squeeze.
Three operating modes can be programmed for PRE-COCKING can be set: HIGH / MID / LOW - each regulates the spring tension in different stages

*PRE-COCKING mode now works in all fire mode selection modes: SEMI, BURST, AUTO and does not require manual calibration

BURST (Gen.2)
The BURST mode, i.e. the firing of a pre-programmed series of shots, only requires the selection of the number of cartridges to be fired (up to 10 cartridges per trigger). This function is very useful in all MILSIMs or when using real low capacity magazines.

ROF CONTROL
This allowed reduce the firing rate of the replica. This means that more powerful Li-Po batteries can be used and still maintain a rate of fire that corresponds to that of real firearms.

ROF STAB
Enables the functionality of ROF CONTROL to be changed:
- ON - RoF Control regulates the cycle speed, which enables smooth operation of the gearbox and less wear on the internal parts of the replica
- OFF - RoF Control adds pauses between each shot to minimise the Rate of fire to reduce the number of kilometres. This makes for a very realistic experience.

SNIPER DELAY
This function can be used to A delay can be set between each shot in SEMI mode to simulate a reload delay or recoil compensation. This is possible, the following Set delays: 0.5s, 1.0s, 2.0s and 3.0s.

A detailed description of all functions can be found on the manufacturer's website: http://www.gatee.eu/

The complete Manual is available at the following address:

http://gatee.eu/images/gate/instrukcje/titan-pl.pdf

The set contains:

- TITAN drop-in module
- USB plug for control via the GATE Control Station app
- Mounting kit
- Quick Start Guide (English)