SA-B14 ONE™ KeyMod 12″ Carabiner Replica (ASCU2 Gen.4+ Version)

Description

SA-B14 KeyMod 12″ Carbine Replica (ASCU2 Gen.4+ Version)

SA-B14 from Specna Arms is largely made from an alloy of zinc and aluminium, with some Steel elements were applied to the most problematic areas of the replica (pins, screws and tactical sling swivels). The SF stock, which holds a battery, and the pistol grip were made of polymer. The body of the replica was subjected to an anodising process, which guarantees a high level of protection against corrosion. The paintwork was carried out by Powder coatingafter the surface has been sandblasted. This type of paint finish makes the paint more abrasion-resistant than usual. The bodywork carries USMC markings.

All parts of the replica go very well together - The gun is built to a standard previously only seen in replicas from well-known brands such as G&P or Classic Army - and it is exceptionally well balanced. All this makes this replica very manoeuvrable and its weight is practically imperceptible when placed on the shoulder.

Equipped with a fast spring opening system, the so-called Enter & Convert™. It enables quick and seamless adjustment of spring strength to the expected conditions on the simulated battlefield without the need for a workshop nearby or access to specialised tools - once the gearbox is removed from the housing, the spring change process takes just a few seconds.

The advantages of Enter & Convert™ cannot be overestimated. In view of the current policy in Europe of adhering to the legally prescribed restrictions on the muzzle velocity of the replica and the regulations for the environment itself, this system guarantees the user far-reaching possibilities and great freedom. The Enter & Cover™ system makes it possible to the main spring in a minimum of time and thus adapt the muzzle velocity of the replica to the conditions of the battlefield, so that the best compromise between firing efficiency and safety of the user and other players is found.

The replica is fully compatible with LiPo and LiFe batteries. The standard main spring guarantees a muzzle velocity of ~420 FPS, which means that the replica also works well at medium distances. The set includes an M90 spring, which makes it possible to reduce the muzzle velocity to ~320 FPS, making the replica suitable for close-range and indoor use.

A gearbox with a reinforced piston head holds a Steel spring sliderwhich is part of the Enter & Cover™ system and 8mm Ball bearings that Steel gears mount. The system is secured by four anti-reverse locks. A lightweight polycarbonate piston has been fitted with steel teeth to increase its durability. Other installed parts include: a type 2 cylinder, a steel interrupter and a metal hop-up chamber.

The replica has a upper 22mm RIS rail and an adjustable stock. The upper RIS rail is equipped with a hinged visor that can be easily removed and replaced with an optical visor. A folding stock with a non-slip butt pad allows the user to adjust the length of the replica to suit their build and preferences. A standard flash hider is mounted on a 14mm left hand thread and can be replaced with a silencer.

This model has a 12″, modular, KeyMod Handguard. The KeyMod module can be used with special segments, such as RIS rails (KeyMod nuts) in any position or configuration through holes around the hand guard (KeyMod slots).

This is an airsoft replica of a KeyMod handguard, the size may differ from the original. We do not guarantee the full compatibility of the KeyMod hand guard with special KeyMod accessories.

To increase the realism, the replica has a functional bolt release mechanism.

The replica is supplied with a steel magazine with a capacity of up to 300 BBs. The colour of the magazine corresponds to the colour theme of magazines for live firearms normally used by the military.

The accessories shown in the photos are not included in the scope of delivery!

This replica was built with the most modern gen.4+ ASCU2 Module which was installed in our service department.

With the latest ASCU gen.4+ module, we get updated software that makes it possible to protects against damagecaused by an inferior Li-Po battery.

The ASCU is a two-part electronic module (the control module and the sensor module) which, once installed in the airsoft replicas, significantly improves their functionality. The traditional hinge module has been replaced by a sensor module that monitors the current position of the piston thread wheel, the firing mode selector lever and the trigger. The information collected is sent to the control module, where the software in the processor analyses it and controls the replica's motor using the active MOSFET interruption.

ASCU Gen. 4 includes the following upgrades:

1. new MosFet transistors with 16 times lower resistance, resulting in a faster cycle, better active brake, more shots per battery charge and less heat.
2. new very strong release switch.
3. New reinforced design with all-polymer housing.
4. better short-circuit protection.
5. easier installation.
6. Updated software with simpler programming (accidental hop-up programme activation is impossible).
7. Improved switch-off lever.
8. improved dial disc.
9. fits all standard and reinforced version 2 gearboxes.
10. 3-year worldwide warranty.

The ASCU improves the operation of a V.3 gearbox and ensures that the replica is on a par with the more expensive replicas and the more sophisticated PTW-class replicas. The ASCU system monitors the operation of the replica regardless of the speed at which the trigger is pulled and is responsible for the entire cycle of piston operation, both in semi-automatic and fully automatic firing modes. The piston stops in the home position after each shot.

The ASCU is equipped with the Low Drain Protection System, which was specially developed to protect the lithium polymer (LiPo) batteries from damage.

In the event of an emergency, the ASCU stops the fire mode in the replica and thus protects the internal elements from further damage.

The ASCU is easy to install in the replica, which is equipped with the V.2 gearbox. For most models, no changes to the original parts of the airsoft rifle are required. In some cases, however, some minor modifications must be made - thanks to these, the installation can be carried out without any problems.

Note:
11.1V or 12V battery is recommended!
7.4V to 8.4V battery, only to be used with M90 to M100 springs.
The use of a high-quality motor with ASCU2 gen.4+ is strongly recommended.
The use of a high-quality rechargeable battery with the ASCU2 gen.4+ is strongly recommended.

The set includes:

- A replica
- A magazine
- Iron sights
- Additional main spring
- One battery
- A charger

INFORMATION

According to the report number HKGEC1600157401

This product is compliant with the EU RoHS (Restriction of Hazardous Substances) Directive 2011/65/EU Annex II, which replaces Directive 2002/95/EC, on the restriction of hazardous substances in toys and electronics.

This means that the Specna Arms brand is free from the following hazardous substances is:
- Lead
- Mercury
- Cadm
- Hexavalent chromium
- Polybrominated biphenyls
- Polybrominated diphenyl ethers
- Bis(20ethylhexyl)phthalate
- Butyl benzyl phthalate
- Dibutyl phthalate
- Diisobutyl phthalate