TITAN™ V2 BASIC Drop-In Controller Set [back-wiring]

TITAN™ V2 BASIC Drop-In Controller Set [Rear-Wired]

Drop-In MOSFET Type TITAN™ V2 Controller Set transforms an AEG into an advanced training replica. It provides a tactical advantage thanks to a lightning-fast trigger response and the ability to modify the replica and customise it for any mission using 20 available functions. This is the most advanced and best model of GATE. 

TITAN™ V2 controller will breathe new life into an ASG electric replica.

Modules in the BASIC version have the following properties:

- AUG mode
- Diagnostic function
- Firmware updates
- Cycle detection
- Setting the trigger sensitivity

ATTENTION! To use all the functions of the ADVANCED version, it is necessary to unlock the FIRMWARE UPGRADE for the ADVANCED Version on www.gatee.eu/editions website.

TITAN™ module functions:
- Setting the trigger sensitivity
- Pre-cocking gain - adjustment of the time the spring is held pulled (shortens the time between pulling the trigger and firing)
- Setting the fire mode selection modes
- Burst mode
- Setting the firing rate
- Low battery notification
- Protecting the battery from damage
- "Sniper delay"
- Full cycle detection
- AUG mode - the option to set two trigger sensitivities (semi and full-auto)

More comprehensive description of the TITAN™ controller:

TRIGGER SENSITIVITY ADJUSTMENT
Five sensors that enable the trigger sensitivity to be controlled. The replica does not need to be dismantled, it is sufficient to use the Tactical Programmer Card or the GATE™ Control Station. This allows the replica to be customised to the user's abilities and individual preferences.

CONFIGURABLE FIRE MODE SELECTOR (GEN. 2)
Two sensors can be programmed in three ways to select one of 6 functions:
- SAFE-SEMI-AUTO
- SAFE-SEMI-SEMI
- SAFE-SEMI-BURST*
- SAFE-BURST*-CAR
- SAFE-SEMI-BURST*/AUTO (short press and hold - BURST, long press and hold the AUTO trigger)
- SAFE-BURST*-AUTO (SAFE via a quick mode selection, if: SAFE-SEMI-SAFE)
*BURST means firing a series of shots.

CYCLE DETECTION
The TITAN™ control unit can precisely recognise the position at which a cycle should end. This means that pulling the trigger completes a full firing cycle (replicas without the TITAN™ system often jam if the trigger is pulled too short and does not end with a shot.
TITAN™ eliminates this error).
The result:
- Automatic BURST mode, with this series the cycle time does not need to be set, only the number of BBs to be fired needs to be specified
- Automatic pre-cocking available in each mode in the following fire mode selector settings: SEMI BURST and AUTO. Unlike conventional MOSFET modules, this setting does not need to be configured manually. Only the power of the spring preload needs to be set.
- ALWAYS FULL CYCLE - when the preload is switched off, TITAN™ ensures that the gear runs through a full cycle and the spring is released after firing. This ensures greater reliability of the replica.

PRE-COCKING (Gen.2*)
Winning a duel often comes down to fractions of a second, which is why the trigger reacts at a speed comparable to that of a real firearm thanks to pre-cocking. As the spring is pulled beforehand, it is also pointed out that using this mode with strong springs leads to faster wear of the internal parts of the replica.
There are two modes of the PRE-COCKING function:
1. AUTO - the spring is pulled after each shot
2. SMART - the spring is preloaded by a slow pressure on the trigger and a shot is released by a fast pressure.
Three operating modes can be programmed for PRE-COCKING can be set: HIGH / MID / LOW - each controls the spring tension in different stages

*PRE-COCKING mode now works in all fire mode selection modes: SEMI, BURST, AUTO and does not require manual calibration

BURST (Gen.2)
BURST mode, i.e. firing a pre-programmed series of shots requires only the selection of the Quantity of cartridges to be fired (up to 10 cartridges per trigger). It is very useful in all MILSIMs or when using real low-cap magazines.

ROF CONTROL
This allows the rate of fire of the replica to be reduced. This makes it possible to use more powerful Li-Po batteries and still achieve a rate of fire that is in line with real firearms.

ROF STAB
Enables the functionality of ROF CONTROL to be changed:
- ON - RoF Control regulates the speed of the cycle, which enables smooth operation of the gearbox and less wear on the internal parts of the replica
- OFF - RoF Control adds pauses between each shot to reduce the rate of fire. This provides a very realistic experience.

SNIPER DELAY
This function can be used to set a delay between each shot in SEMI mode to simulate a reload delay or recoil compensation. It is possible to set the following delays: 0.5 s, 1.0 s, 2.0 s and 3.0 s.

A detailed description of all functions can be found on the manufacturer's website: http://www.gatee.eu/

The complete manual is available at the following address:

http://gatee.eu/images/gate/instrukcje/titan-pl.pdf

The set contains:

- TITAN module with BASIC software

ATTENTION!  To configure the TITAN system, it is necessary to use the USB link or the tactical programming card, which are not included in the set and must be purchased separately.