TITAN™ V2 NGRS BASIC [Front Wired] Controller Set

TITAN V2 NGRS BASIC [Front Wired] Controller Set

Drop-In mosfet Type TITAN™ Controller Set transforms Tokyo Marui V2 Next Generation Recoil Shock into an advanced training replica. It provides a tactical advantage thanks to a lightning-fast trigger response with the ability to modify the replica and customise it for any mission using 20 available functions.

Modules in the BASIC version have the following properties:

- AUG mode
- Diagnostic function
- Firmware updates
- Cycle detection
- Setting the trigger sensitivity

ATTENTION!InTo use all the functions of the ADVANCED version, it is necessary, FIRMWARE UPGRADE for the ADVANCED version on the website www.gatee.eu/editions.

TITAN™ offers new possibilities:
- Setting the trigger sensitivity
- Pre-cocking gain - adjustment of the time the spring is held pulled (shortens the time between pulling the trigger and firing)
- Setting the fire mode selection modes
- Burst mode
- Setting the firing rate
- Low battery notification
- Protecting the battery from damage
- "Sniper delay"

More comprehensive description of the TITAN™ controller:

TRIGGER SENSITIVITY ADJUSTMENT
The third generation of the proximity sensor enables the trigger sensitivity to be controlled. It is not necessary to dismantle the replica, it is sufficient to use the GATE™ control station. This allows the replica to be customised to the user's abilities and individual preferences.

CONFIGURABLE FIRE MODE SELECTOR (GEN. 2)
Two sensors can be programmed in three ways to select one of 6 functions:
- SAFE-SEMI-AUTO
- SAFE-SEMI-SEMI
- SAFE-SEMI-BURST*
- SAFE-BURST*-CAR
- SAFE-SEMI-BURST*/AUTO (short press and hold - BURST, long press and hold AUTO)
- SAFE-BURST*-AUTO (SAFE via a quick mode selection, if: SAFE-SEMI-SAFE)
*BURST means the firing of a series of shots.

CYCLE DETECTION
The TITAN™ control unit can precisely recognise the position at which a cycle should end. This means that pulling the trigger completes a full firing cycle (replicas without the TITAN™ system often jam if the trigger is pulled too short and does not end with a shot. TITAN™ eliminates this error).
The result:
- Automatic BURST mode, with this series the cycle time does not need to be set, only the number of BBs to be fired needs to be specified
- Automatic pre-cocking available in each mode in the following fire mode selector settings: SEMI BURST and AUTO. Unlike conventional MOSFET modules, this setting does not need to be configured manually. Only the power of the spring preload needs to be set.
- ALWAYS FULL CYCLE - when the preload is switched off, TITAN™ ensures that the transmission runs through a full cycle and the spring is released after firing. This ensures greater reliability of the replica.

PRECOMMENDATION (Gen.2*)
Winning a duel often comes down to fractions of a second. This is why the trigger reacts at a speed comparable to that of a real firearm thanks to the preload. As the spring is pulled beforehand, it is also pointed out that using this mode with strong springs leads to faster wear of the internal parts of the replica.
There are two modes of the PRE-COCKING function:
1. AUTO - the spring is pulled after each shot
2. SMART - the spring is preloaded by pulling the trigger slowly and a shot is fired by pulling it quickly.
Three operating modes can be programmed for PRE-COCKING can be set: HIGH / MID / LOW - each regulates the spring tension in different stages

*PRE-COCKING mode now works in all fire mode selection modes: SEMI, BURST, AUTO and does not require manual calibration

BURST (Gen.2)
BURST mode, i.e. the firing of a pre-programmed series of shots, only requires the selection of the Quantity of cartridges to be fired (up to 10 cartridges per trigger). It is very useful in all MILSIMs or when using real low capacity magazines.

ROF CONTROL
This allows the rate of fire of the replica to be reduced. This makes it possible to use more powerful Li-Po batteries and still achieve a rate of fire that is in line with real firearms.

ROF STAB
Enables the functionality of ROF CONTROL to be changed:
- ON - RoF Control regulates the speed of the cycle, which enables smooth operation of the gearbox and less wear on the internal parts of the replica
- OFF - RoF Control adds pauses between each shot to reduce the rate of fire. This provides a very realistic experience.

SNIPER DELAY
This function allows you to set a delay between each shot in SEMI mode to simulate a reload delay or recoil compensation. It is possible to set the following delays: 0.5 s, 1.0 s, 2.0 s and 3.0 s.

A detailed description of all functions can be found on the manufacturer's website: http://www.gatee.eu/

The complete manual is available at the following address:

https://gatee.eu/pl/produkty/titan/ttn-v2-ngrs-pl

The set contains:

- TITAN with BASIC firmware

NOTE! To configure TITAN, you need the USB-Link or Tactical Programming Card, which is not included in this kit.