Titan V2 Basic Module Rear Wired Semi Only

Description

This Mosfet is intended for the German market and can only be used for semi-automatic firing. Conversion or reprogramming to fully automatic is not possible.

TITAN™ is a drop-in MOSFET that transforms your AEG into an advanced training weapon system. Extremely fast trigger response and 20 special functions give the user the tactical advantage of adapting the rifle's capability to any mission requirement.

This version is intended for rifles with rear wiring and for the German market. It can only be used for semi-automatic shooting and conversion or reprogramming to fully automatic is not possible.

The TITAN V2™ Basic module is the optimal cost-effective option for users with TITAN in two or more airsoft guns, as the user does not need the second USB link from the Advanced or Complete Set. It contains TITAN with BASIC firmware edition.

The BASIC firmware edition is a low-cost version with a limited number of functions, intended for those who prefer simplicity but require the highest quality. If you opt for more functions, there is always the option of upgrading the firmware from BASIC to ADVANCED.

Most important functions:

TRIGGER SENSITIVITY ADJUSTMENT - allows the trigger sensitivity to be adjusted to the user's preferences and abilities without having to disassemble the rifle.

CONFIGURABLE FIRE SELECTOR LEVER (gen.2) - offers the possibility to programme the fire selector lever. Up to six modes are available: - STOCK WIRING SEMI/AUTO

CYCLE DETECTION - TITAN recognises precisely in which position the cycle should be ended. This means that even the shortest pull-off process results in at least one full cycle.

PRE-COCKING (gen.2) - ensures a trigger response like that of a real gun. It enables an initial spring compression that significantly accelerates the trigger response. There are three BOOST options: HIGH / MID / LOW and PRE-COCKING MODE:

• AUTO MODE - the spring is automatically compressed after each shot,
• TRIGGER MODE - the first trigger pull compresses the spring and the second trigger pull releases the shot.

ROF STAB - allows you to change the mode of operation of the ROF control unit:

• ON - ROF Control uses PWM to reduce the ROF. This makes the gearbox work more evenly, which reduces wear on the internal parts of the AEG.
• OFF - ROF Control adds pauses between shots to reduce the ROF. This provides a more realistic experience.

SNIPER DELAY - inserts a delay between each SEMI shot to simulate the delay caused by reloading or recoil. It can be set to 0.5s, 1s, 2s or 3s delay.

SMART TRIGGER - enables a faster trigger response. It works with the ROF Control System. During the first shot, the microprocessor sets the ROF Control to 100%. After the first shot, it switches to a previously programmed value (e.g. 50%). As a result, the first shot is fired at full rate of fire and subsequent shots are fired at reduced ROF.

BATTERY PROTECTION (gen.2) - against over-discharge of the battery. The microprocessor constantly monitors the battery voltage. If the voltage drops to a critical level, the controller will not allow any shots to be fired. If the battery voltage drops to a predefined level, the motor vibrates at regular intervals.

SMART FUSE - electronic fuse with an accurate current sensor. A combination of current, voltage and temperature measurement makes an AEG installation extremely reliable. It protects the MOSFET from overheating, overloading and short circuits. If your airsoft gun jams, the function protects the motor and battery from damage.

The MOSFET transfers the energy from the battery directly to the motor, bypassing the conventional mechanical trigger contacts. This gives the replica a higher rate of fire, a faster trigger response and the contacts are protected from burning out.

BUILT-IN SELF-TEST - This allows you to quickly check whether the appliance is working properly.

COATING - Thanks to the special coating, the product is weather-resistant (military specification MIL-V-173C).

Included in the kit:

• TITAN V2 with BASIC firmware edition (wired at the rear)
• Installation kit
• Quick start guide

NOTE! To configure the TITAN, you need the USB link or the Tactical Programming Card, which is not included in this kit.